Merging AirbusX with exterior PA A319, VC to low possion

Forum rules
Community-driven support for Project Airbus aircraft only.
Community-driven support for Project Airbus aircraft only.
Community-driven support for Project Airbus aircraft only.
Community-driven support for Project Airbus aircraft only.
Community-driven support for Project Airbus aircraft only.
Community-driven support for Project Airbus aircraft only.

Please read the pinned topics and search the forum before posting to make sure your question's not already been answered.
Post Reply
kleineMax
Posts: 4
Joined: 10 Jul 2011, 22:36

Merging AirbusX with exterior PA A319, VC to low possion

Post by kleineMax »

Hi,

im using a merge, AirbusX VC with your exterior A319 model. The problem is that the VC has lower position as it should have relative to the extrior, this is because of the different 0-Position Project Airbus and Aerosoft use.
Now i tried to move the PA A319 with ModelconverterX but after exporting the model was messed up.

My question now: Can you guys please provide an PA A319 mdl (A319_100_CFM_NoVC.mdl) that is moved 1,1 units down? That was the value i used in MCX and it lines the x axis (z-layer) with the center of the windshield.

It would be a nice move by you guys.

Regards
Max

GaryG
Posts: 888
Joined: 19 Jul 2009, 10:32

Re: Merging AirbusX with exterior PA A319, VC to low possion

Post by GaryG »

99.9999% it won't be done, the reason I think is fairly obvious.

Regards

kleineMax
Posts: 4
Joined: 10 Jul 2011, 22:36

Re: Merging AirbusX with exterior PA A319, VC to low possion

Post by kleineMax »

I understand that it is work that needs to be done, but thats the only reason i could think about.

Realy no chance? :cry:

Derek Mayer
Posts: 236
Joined: 02 Jul 2009, 16:13

Re: Merging AirbusX with exterior PA A319, VC to low possion

Post by Derek Mayer »

Couldn't you just move the eyepoint in the aircraft.cfg to match the one used by aerosoft?

kleineMax
Posts: 4
Joined: 10 Jul 2011, 22:36

Re: Merging AirbusX with exterior PA A319, VC to low possion

Post by kleineMax »

Allready did that, but cause the VC is possitioned via the 0-Position of the the two models (exterior and VC). It is still 2 Feet (or so) to low. I noticed that when i looked out of the window next to a finger gate and the finger was way higher relative to the cockpit window when looking from the VC to the outside, then viewing it from the outside-view.
I asked at fsdeveloper about that and they told me the same: http://fsdeveloper.com/forum/showthread.php?t=63505

Ghostmaster
Posts: 122
Joined: 04 Dec 2010, 13:36

Re: Merging AirbusX with exterior PA A319, VC to low possion

Post by Ghostmaster »

Its not the eyepoint. It the model itself.

Derek Mayer
Posts: 236
Joined: 02 Jul 2009, 16:13

Re: Merging AirbusX with exterior PA A319, VC to low possion

Post by Derek Mayer »

Yeah there's no fix then, sorry.

kleineMax
Posts: 4
Joined: 10 Jul 2011, 22:36

Re: Merging AirbusX with exterior PA A319, VC to low possion

Post by kleineMax »

There would be one ;)

But its ok! You dont want to do it, of course you dont have to do it ;)

Thy anyway for responding.

Post Reply