Project FMC simplified for Project Airbus
Re: Project FMC simplified for Project Airbus
Station load 7 is a full rear small compartiment, that not accept container :
I think that is used for large bulky objects, that don't enter in standard containers.
I think that is used for large bulky objects, that don't enter in standard containers.
Re: Project FMC simplified for Project Airbus
I work on tanks location. If attitude change with fuel level, I think that is the solution. I think that tanks are placed closest of CG in real aircraft; the most logical....Prosdocimo wrote:Hi I changed cruise_lift_scalar to 0.9 and these are the results:
FL390, 0.77M
Fuel 50%: pitch -3.89
Fuel 25%: pitch: -3.24
Fuel 10%: pitch: -2.74
FL350, 0.77M
Fuel 50%: pitch -2.44
Fuel 25%: pitch: -1.91
Fuel 10%: pitch: -1.63
FL300, 0.77M
Fuel 50%: pitch -1.12
Fuel 25%: pitch: -0.68
Fuel 10%: pitch: -0.45
At FL300 it seems good but too much pitch at FL390. Maybe set cruise_lift to 0.95 could be better?
Edit:
François, is it right the weight in station_load.7=605 ?
The .5 is 6050
Re: Project FMC simplified for Project Airbus
I solved the bug, about Pitot icing.
When pitot was iced, sometimes, Pitot stayed failed, even if pitot heat was activated.
I added new code to remove Pitot blockage; After press Pitot heat switch, wait 20 to 40 seconds, and pitot will work again.
Panels will be updated next week.
François
When pitot was iced, sometimes, Pitot stayed failed, even if pitot heat was activated.
I added new code to remove Pitot blockage; After press Pitot heat switch, wait 20 to 40 seconds, and pitot will work again.
Panels will be updated next week.
François
-
- Posts: 277
- Joined: 10 Oct 2014, 12:05
Re: Project FMC simplified for Project Airbus
Great! It was a bug I had
Re: Project FMC simplified for Project Airbus
I had Not enough time to update panel this weekend. Sorry, next weekend. Many works on the A321.....
But I updated the Airport creation toolkit (v4.12) with new user manual about Holding pattern with 2 altitude constraints :
In english : http://freenavdbgroup.com/?page_id=397
In French : http://freenavdbgroup.com/?page_id=212
When A321 will be completed, I will work on A380 (probably based on the A340 Tom Ruth's VC but with FD-FMC gauges, because it seems that the FS9 A380 VC occurs some FPS hit in FSX) with transoceanic routes (NATS & PACOTS).
I must ask the permission to Tom Ruth
François
But I updated the Airport creation toolkit (v4.12) with new user manual about Holding pattern with 2 altitude constraints :
In english : http://freenavdbgroup.com/?page_id=397
In French : http://freenavdbgroup.com/?page_id=212
When A321 will be completed, I will work on A380 (probably based on the A340 Tom Ruth's VC but with FD-FMC gauges, because it seems that the FS9 A380 VC occurs some FPS hit in FSX) with transoceanic routes (NATS & PACOTS).
I must ask the permission to Tom Ruth
François
Re: Project FMC simplified for Project Airbus
Hello Francois,
The development of the program FD_FMC SID STAR precedes (Prof. version).
This version I'm working on will take some time.
Therefore I have decided to present a simpler version (Lite).
This still needs an installer and a manual. (3-4 Weeks it will be done).
What are the features of the Prof. version ?
Automatic creation of all csv files from a Navigraph Cycle.
Automatic adjustment of available waypoints.
with LAT LON data from the following data.
a.) PlanG database.
b.) OR generated by makerwys Pete Dowson files.
c.) OR Navigraph Cycle Data.
An import existing airport takes 1 minute.
Then you can new SID, STARS create or modify existing ones.
automatic copy of all files in the right directories
compilation (optional)
A generation of all csv, txt, xml, bgl from Navigraph data
A normal Airport as EDDW needs
a.) Reading the data
b.) Check, Fine Tuning
c.) Creating the Airport .txt file
d.) Creating csv, xml files
e.) bgl compile xml file
takes between 15 to 25 minutes.
What can the Lite version ?
a.) Import existing airport
b.) autofind existing waypoints from PlanG
c.) generates all files ( No need to look for too much commas)
d.) manual creation of SID and STAR
e.) auto update from lowercase to upercase (type ed eddw udado, will be updated to ED EDDW UDADO
f.) automatic controll of decimal signs. 52.99910875 will be converted to 52.999109
g.) Add+ a new waypoint, with arrow up/down move it to the right position. Total Number of WPT will be incremented.
etc.
Here a screenshot of the SID -DATA / SID -INDEX Form
I hope you like it
Thomas
The development of the program FD_FMC SID STAR precedes (Prof. version).
This version I'm working on will take some time.
Therefore I have decided to present a simpler version (Lite).
This still needs an installer and a manual. (3-4 Weeks it will be done).
What are the features of the Prof. version ?
Automatic creation of all csv files from a Navigraph Cycle.
Automatic adjustment of available waypoints.
with LAT LON data from the following data.
a.) PlanG database.
b.) OR generated by makerwys Pete Dowson files.
c.) OR Navigraph Cycle Data.
An import existing airport takes 1 minute.
Then you can new SID, STARS create or modify existing ones.
automatic copy of all files in the right directories
compilation (optional)
A generation of all csv, txt, xml, bgl from Navigraph data
A normal Airport as EDDW needs
a.) Reading the data
b.) Check, Fine Tuning
c.) Creating the Airport .txt file
d.) Creating csv, xml files
e.) bgl compile xml file
takes between 15 to 25 minutes.
What can the Lite version ?
a.) Import existing airport
b.) autofind existing waypoints from PlanG
c.) generates all files ( No need to look for too much commas)
d.) manual creation of SID and STAR
e.) auto update from lowercase to upercase (type ed eddw udado, will be updated to ED EDDW UDADO
f.) automatic controll of decimal signs. 52.99910875 will be converted to 52.999109
g.) Add+ a new waypoint, with arrow up/down move it to the right position. Total Number of WPT will be incremented.
etc.
Here a screenshot of the SID -DATA / SID -INDEX Form
I hope you like it
Thomas
-
- Posts: 501
- Joined: 20 Jan 2014, 21:27
Re: Project FMC simplified for Project Airbus
No A319 to complete the single aisle Airbus´ at first?fdd_fr wrote: When A321 will be completed, I will work on A380 (probably based on the A340 Tom Ruth's VC but with FD-FMC gauges, because it seems that the FS9 A380 VC occurs some FPS hit in FSX) with transoceanic routes (NATS & PACOTS).
-
- Posts: 277
- Joined: 10 Oct 2014, 12:05
Re: Project FMC simplified for Project Airbus
In my opinion we have already A318, A320 and A321. In case of a next twin engine airbus, i'd like fly A330 instead
Thanks Thomas your job is amazing! Even if I'm not an airport creator so i will not use it
Thanks Thomas your job is amazing! Even if I'm not an airport creator so i will not use it
Re: Project FMC simplified for Project Airbus
If you ever fly with a ATC Controller like PROATC/XProsdocimo wrote: Thanks Thomas your job is amazing! Even if I'm not an airport creator so i will not use it
You can hardly follow the advices by ATC
PROATC/X , FS Commander and other tools using DATA from an Navigraph cycle.
All Tools must use the same cycle.
One User has cycle 1406 an other 1602.
It's not important what cycle you have, but to be insync all Tools have to use the same cycle.
The user A is only interested on flights in Europe the other user B likes to fly in the USA.
User A needs Airports in Europe the other in the USA.
Both needs a tool to create their own favorite Airports (SID / STAR), wich are used by FD-FMC.
The success of Project FMC simplified depends on how easy it is for a normal user to create his favorite airport (sid / star) itself.
Or he waits until this airport from other is created.
The favorite airports not exist ! Less fun.
Thomas
-
- Posts: 354
- Joined: 29 Jul 2014, 22:47
Re: Project FMC simplified for Project Airbus
Wulf, I agree with your idea.wulfbindewald wrote:No A319 to complete the single aisle Airbus´ at first?fdd_fr wrote: When A321 will be completed, I will work on A380 (probably based on the A340 Tom Ruth's VC but with FD-FMC gauges, because it seems that the FS9 A380 VC occurs some FPS hit in FSX) with transoceanic routes (NATS & PACOTS).
Re: Project FMC simplified for Project Airbus
moskito-x wrote:Hello Francois,
The development of the program FD_FMC SID STAR precedes (Prof. version).
This version I'm working on will take some time.
Therefore I have decided to present a simpler version (Lite).
This still needs an installer and a manual. (3-4 Weeks it will be done).
What are the features of the Prof. version ?
Automatic creation of all csv files from a Navigraph Cycle.
Automatic adjustment of available waypoints.
with LAT LON data from the following data.
a.) PlanG database.
b.) OR generated by makerwys Pete Dowson files.
c.) OR Navigraph Cycle Data.
An import existing airport takes 1 minute.
Then you can new SID, STARS create or modify existing ones.
automatic copy of all files in the right directories
compilation (optional)
A generation of all csv, txt, xml, bgl from Navigraph data
A normal Airport as EDDW needs
a.) Reading the data
b.) Check, Fine Tuning
c.) Creating the Airport .txt file
d.) Creating csv, xml files
e.) bgl compile xml file
takes between 15 to 25 minutes.
What can the Lite version ?
a.) Import existing airport
b.) autofind existing waypoints from PlanG
c.) generates all files ( No need to look for too much commas)
d.) manual creation of SID and STAR
e.) auto update from lowercase to upercase (type ed eddw udado, will be updated to ED EDDW UDADO
f.) automatic controll of decimal signs. 52.99910875 will be converted to 52.999109
g.) Add+ a new waypoint, with arrow up/down move it to the right position. Total Number of WPT will be incremented.
etc.
Here a screenshot of the SID -DATA / SID -INDEX Form
I hope you like it
Thomas
Hello Thomas,
Your soft sounds great !!!
I haven't Navigraph data and I don't know how they are formatted; But is the speed information about STAR or approach are include in these files ?
wulfbindewald wrote:No A319 to complete the single aisle Airbus´ at first?fdd_fr wrote: When A321 will be completed, I will work on A380 (probably based on the A340 Tom Ruth's VC but with FD-FMC gauges, because it seems that the FS9 A380 VC occurs some FPS hit in FSX) with transoceanic routes (NATS & PACOTS).
A319 will be done also. But since 4 years that I work on A32x serie, I would like to change of Aircraft....I need some new horizon....
I will try to do A319 in the same time.
Re: Project FMC simplified for Project Airbus
Hello Francois,Hello Thomas,
Your soft sounds great !!!
I haven't Navigraph data and I don't know how they are formatted; But is the speed information about STAR or approach are include in these files ?
an excerpt from EDDW.xml Navigraph
Thomas
Re: Project FMC simplified for Project Airbus
I did not know that navigraph data was in XML format. Keep your work moskito !
For members who had downloaded beta A321 CFM, here an panel update :
http://freenavdbgroup.com/download/Pane ... 201.16.zip
This update contains :
- New AIR file updated (better thrust at low throttle and to take off, improve cruise attitude)
- new aircraft.cfg file
- new panel with following features :
- Fuel system completed, with 3 central tanks : lower ECAM updated;
- New security : You cannot engage LOC/APPR pb, if a holding is armed or engaged,
- New security : you cannot arm or engage an holding if LOC/APPR is activated
- In previous version, if Pitot was iced, system can stay out of order even if pitot heater was activated (fsx bug); Now, pitot deicing works in all case (wait 20 to 40 seconds)
- In descent page, if a holding has an exit altitude lower than the entry altitude, this exit alaitude is displayed, with a blink text to think that you have to run this mandatory holding pattern.
- New V1 V2 VR calculation for A321
If these updates are validate, I will update A318 and A320 with these features.
Small delay for Airport database update; Tomorrow, in the morning;
Francois
For members who had downloaded beta A321 CFM, here an panel update :
http://freenavdbgroup.com/download/Pane ... 201.16.zip
This update contains :
- New AIR file updated (better thrust at low throttle and to take off, improve cruise attitude)
- new aircraft.cfg file
- new panel with following features :
- Fuel system completed, with 3 central tanks : lower ECAM updated;
- New security : You cannot engage LOC/APPR pb, if a holding is armed or engaged,
- New security : you cannot arm or engage an holding if LOC/APPR is activated
- In previous version, if Pitot was iced, system can stay out of order even if pitot heater was activated (fsx bug); Now, pitot deicing works in all case (wait 20 to 40 seconds)
- In descent page, if a holding has an exit altitude lower than the entry altitude, this exit alaitude is displayed, with a blink text to think that you have to run this mandatory holding pattern.
- New V1 V2 VR calculation for A321
If these updates are validate, I will update A318 and A320 with these features.
Small delay for Airport database update; Tomorrow, in the morning;
Francois
-
- Posts: 501
- Joined: 20 Jan 2014, 21:27
Re: Project FMC simplified for Project Airbus
The sub-folder A321FD-FMC is located in the panel.A321CFM panel folder.
To be located into the FSX/Gauges folder or to stay as is?
To be located into the FSX/Gauges folder or to stay as is?
-
- Posts: 277
- Joined: 10 Oct 2014, 12:05
Re: Project FMC simplified for Project Airbus
Hi thank you! Attitude is ok to me. I found two things. The first tanks used are the central ones and not the wing's. Shoudn't be on the contrary? During the switch between a finished central tank and the new central one the engines seem stopping and starting again.
Re: Project FMC simplified for Project Airbus
no importance. A gauge folder can be in panel folder or FSX gauge folder. Same thing.wulfbindewald wrote:The sub-folder A321FD-FMC is located in the panel.A321CFM panel folder.
To be located into the FSX/Gauges folder or to stay as is?
During beta, I place it in panel folder : more easy for me to work on files.
With final version, as FD-FMC is comon to CFM and IAE version, I will place it in Gauge folder : 1 CAB file for 2 aircraft version.
I will check that. Maybe I should toggle center tanks valve before tanks become empty.Prosdocimo wrote:Hi thank you! Attitude is ok to me. I found two things. The first tanks used are the central ones and not the wing's. Shoudn't be on the contrary? During the switch between a finished central tank and the new central one the engines seem stopping and starting again.
I will test.....
Re: Project FMC simplified for Project Airbus
About tanks feeding order, FSX aircrafts are false. In FSX, wings tanks are used in first
Real sheme: Fuel must be pumped in central tank(s) before, after finishing by wings.
This is the reason of the fuel_system gauge; Get the true fuel sheme.
Francois
Real sheme: Fuel must be pumped in central tank(s) before, after finishing by wings.
This is the reason of the fuel_system gauge; Get the true fuel sheme.
Francois
Last edited by fdd_fr on 28 Feb 2016, 14:59, edited 1 time in total.
Re: Project FMC simplified for Project Airbus
Airports database updated :
NEW :
- EHGG – Groningen – Netherlands by Martien Van Rooten : Provided with an updated AFCAD
- KBUR – Burbanks Bob Hope – USA (California) by Wulf Bindewald
- KFCA – Kalispell Glacier National Park – USA (Montana) by Wulf Bindewald
- LFML – Marseilles Porvence – France – by francois Dore : Version with actual runway designator if you use a addon scenery
- LIBR – Brindisi – Italy by Georges
- LICR – Reggio Calabria – Italy by Francois Dore
Updates :
- EHBK – Maastricht : fix SID data issue
- KWYS – Yellowstone USA : Updated by Wulf
- SKBO – Bogota – Columbia, updated by Carlos
New AIRAC file : 02272016
Next update : March 12th
Expected airports :
KMCI - Kansas City
KBWI – Washington Baltimore
.......
NEW :
- EHGG – Groningen – Netherlands by Martien Van Rooten : Provided with an updated AFCAD
- KBUR – Burbanks Bob Hope – USA (California) by Wulf Bindewald
- KFCA – Kalispell Glacier National Park – USA (Montana) by Wulf Bindewald
- LFML – Marseilles Porvence – France – by francois Dore : Version with actual runway designator if you use a addon scenery
- LIBR – Brindisi – Italy by Georges
- LICR – Reggio Calabria – Italy by Francois Dore
Updates :
- EHBK – Maastricht : fix SID data issue
- KWYS – Yellowstone USA : Updated by Wulf
- SKBO – Bogota – Columbia, updated by Carlos
New AIRAC file : 02272016
Next update : March 12th
Expected airports :
KMCI - Kansas City
KBWI – Washington Baltimore
.......
-
- Posts: 277
- Joined: 10 Oct 2014, 12:05
Re: Project FMC simplified for Project Airbus
Yes it seems not working as the first tanks that are emptied first are the central ones and not the wing's. In a318 and a320 it's correct. I also realized that the central #1 and #3 go to zero. Meanwhile in the #2 there is a leftover when wing's tanks are switched.
Re: Project FMC simplified for Project Airbus
i check....
Re: Project FMC simplified for Project Airbus
order is ok :
Tank central 3 (central backward)
then
Tank central 2 (central forward)
then central 1 (main center)
then wings
bugs when toggle from center 3 to 2 or 2 to 1. Engines slow down then start again. I must toggle pumps and valves before that tanks are empty.
Tank central 3 (central backward)
then
Tank central 2 (central forward)
then central 1 (main center)
then wings
bugs when toggle from center 3 to 2 or 2 to 1. Engines slow down then start again. I must toggle pumps and valves before that tanks are empty.
Re: Project FMC simplified for Project Airbus
This sheme is the right sheme.Prosdocimo wrote:Yes it seems not working as the first tanks that are emptied first are the central ones and not the wing's. In a318 and a320 it's correct. I also realized that the central #1 and #3 go to zero. Meanwhile in the #2 there is a leftover when wing's tanks are switched.
Center in first, wings after.
A318 and A320 use the same sheme.
Re: Project FMC simplified for Project Airbus
Here, fuel system gauge fixed for A321 ---> http://freenavdbgroup.com/download/Pane ... system.zip
Unzip A321_Fuel_system.xml file and place it in "panel.A321CFM\A321FD-FMC" folder
This update fix the shut down engine issue when center tank 2 or center tank 3 is empty.
Unzip A321_Fuel_system.xml file and place it in "panel.A321CFM\A321FD-FMC" folder
This update fix the shut down engine issue when center tank 2 or center tank 3 is empty.
-
- Posts: 354
- Joined: 29 Jul 2014, 22:47
Re: Project FMC simplified for Project Airbus
Francois, I did a flight from EHAM to EGCC and I discovered a flaw in the EGCC approach data: current runways are 05L/23R and 05R/23L, but in the FD-FMC, the runways are 06L/24R and 06R/24L.
Could you please correct that? Thanks.
Could you please correct that? Thanks.
-
- Posts: 501
- Joined: 20 Jan 2014, 21:27
Re: Project FMC simplified for Project Airbus
Hi there,
sometimes it is helpfull to compare how real airliners are following official arrivals/approach. Enclosed a pic which shows a REAL landing track from a MD11F in KONT Ontario, California, today (left pic) and the defined ZIGGY5 arrival in FSX (right pic) with the A321 panel 1.16. KONT is under test and will be provided soon.
Wulf
sometimes it is helpfull to compare how real airliners are following official arrivals/approach. Enclosed a pic which shows a REAL landing track from a MD11F in KONT Ontario, California, today (left pic) and the defined ZIGGY5 arrival in FSX (right pic) with the A321 panel 1.16. KONT is under test and will be provided soon.
Wulf
Re: Project FMC simplified for Project Airbus
Ok. It will be done for next database update.The320Pilot wrote:Francois, I did a flight from EHAM to EGCC and I discovered a flaw in the EGCC approach data: current runways are 05L/23R and 05R/23L, but in the FD-FMC, the runways are 06L/24R and 06R/24L.
Could you please correct that? Thanks.
wulfbindewald wrote:Hi there,
sometimes it is helpfull to compare how real airliners are following official arrivals/approach. Enclosed a pic which shows a REAL landing track from a MD11F in KONT Ontario, California, today (left pic) and the defined ZIGGY5 arrival in FSX (right pic) with the A321 panel 1.16. KONT is under test and will be provided soon.
Wulf
It's a pleasure to see that our work offers a better reality to our sim
-
- Posts: 354
- Joined: 29 Jul 2014, 22:47
Re: Project FMC simplified for Project Airbus
Well, let me elaborate. UK2000 Manchester Xtreme shows the current runways (05L/R and 23L/R). I don't what are the runways in the default FSX.fdd_fr wrote:Ok. It will be done for next database update.The320Pilot wrote:Francois, I did a flight from EHAM to EGCC and I discovered a flaw in the EGCC approach data: current runways are 05L/23R and 05R/23L, but in the FD-FMC, the runways are 06L/24R and 06R/24L.
Could you please correct that? Thanks.
Re: Project FMC simplified for Project Airbus
Defaut FSX EGCC has runway 06/24. So Jean-Pierre Varnier who has realized EGCC Freenav files, did it according default FSX airport.
UK2000 Scenery use the actual runway name. So I will prepare this week-end an version with actual runway name; This easy and quick to change data, and no AIRAC update required. I did it last weekend for LFML.
I will upload saturday.
Francois
UK2000 Scenery use the actual runway name. So I will prepare this week-end an version with actual runway name; This easy and quick to change data, and no AIRAC update required. I did it last weekend for LFML.
I will upload saturday.
Francois
-
- Posts: 501
- Joined: 20 Jan 2014, 21:27
Re: Project FMC simplified for Project Airbus
A320/321 speed brakes efficiency during flight:
When I activate the speed brakes in the A320 V1.15 or in the A321 V1.16 and AP is activated, then the speed brake lever arm moves to 100%. For the A320 the efficincy during flight should be max 50%, but for A321 the setting for 100% is correct acc. to the pilots blog below. For your info.
http://www.pprune.org/tech-log/428355-a ... p-des.html
When I activate the speed brakes in the A320 V1.15 or in the A321 V1.16 and AP is activated, then the speed brake lever arm moves to 100%. For the A320 the efficincy during flight should be max 50%, but for A321 the setting for 100% is correct acc. to the pilots blog below. For your info.
http://www.pprune.org/tech-log/428355-a ... p-des.html
-
- Posts: 354
- Joined: 29 Jul 2014, 22:47
Re: Project FMC simplified for Project Airbus
VC day lighting (toggled with the Recognition light switch) doesn't work in the A321.
-
- Posts: 277
- Joined: 10 Oct 2014, 12:05
Re: Project FMC simplified for Project Airbus
To me it works but it's just a little weak
Re: Project FMC simplified for Project Airbus
If I understand, speed brakes can extend at 100% with AP for A318, A319 and A321 and only A320 has 1/2 speed brakes.wulfbindewald wrote:A320/321 speed brakes efficiency during flight:
When I activate the speed brakes in the A320 V1.15 or in the A321 V1.16 and AP is activated, then the speed brake lever arm moves to 100%. For the A320 the efficincy during flight should be max 50%, but for A321 the setting for 100% is correct acc. to the pilots blog below. For your info.
http://www.pprune.org/tech-log/428355-a ... p-des.html
Correct ?
Check your light section in aircraft.cfg :The320Pilot wrote:VC day lighting (toggled with the Recognition light switch) doesn't work in the A321.
[lights]
//Types: 1=beacon, 2=strobe, 3=navigation, 4=cockpit, 5=landing 6=taxi, 7=recognition, 8=wing, 9=logo
light.0=3, -77.90, -0.15, 4.80, fx_navwhih
light.1=2, -77.90, 0.15, 4.80, fx_strobeh
light.2=1, 6.80, 0.00, -5.80, fx_beaconh
light.3=1, 3.83, 0.00, 8.47, fx_beaconh
light.4=5, 11.57, -10.48, -5.91, fx_PAland
light.5=5, 11.57, 10.48, -5.91, fx_PAland
light.6=9, -67.88, 8.99, 18.45, fx_pa380logo
light.7=9, -67.88, -8.99, 18.45, fx_pa380logo
light.8=7, 59.50, -1.00, 3.00, fx_vclighth // VC Day Lighting eclairage jour <-- VC day (recog switch)
light.9=4, 57.00, 0.00, 6.00, fx_vclighth // eclairage nuit Cockpit
I agree that lighting must be imporved, but current works (not perfect)
I am finishing to test a new table 404 (Wing Angle of Attack versus Wing Coefficient lift); It seems that after many test, I am close to a very good behavior.
It fix the actual airfile that you use, which occurs a nose too down at high speed and low/middle altitude (not realistic).
I edited empty weight center of gravity for a better trim stability.
I hope post this new airfile and aircraft.cfg file tonight.
When airfile will be ok, aircraft will be ready.
Francois
On my computer, landing lights and taxi lights are very "light"; I think that I must change the beam orientation; Your advice ?
-
- Posts: 277
- Joined: 10 Oct 2014, 12:05
Re: Project FMC simplified for Project Airbus
About landing lights, probably there is an issue on nose gear's lights direction. If you watch at it by the front, you can see four lights. Two small lower (both taxi lights) and two upper (a small one on the left that is a taxi again, and a larger one on the right that is a landing light). Now these two upper lights seem badly oriented as you can see just a light spot down the gear and not forward. The bottom small lights and the wing's seem ok.
Edit. I looked on the web, it seems that landing and taxi lights are kept both on during landings and take off. This may help to increase the light intensity here.
Edit2. I made some tests and i guess your A318 displays perfect taxi/landings lights. You could copy those settings to A321
Edit. I looked on the web, it seems that landing and taxi lights are kept both on during landings and take off. This may help to increase the light intensity here.
Edit2. I made some tests and i guess your A318 displays perfect taxi/landings lights. You could copy those settings to A321
Last edited by Prosdocimo on 06 Mar 2016, 20:31, edited 1 time in total.
-
- Posts: 354
- Joined: 29 Jul 2014, 22:47
Re: Project FMC simplified for Project Airbus
I haven't tested the A321 during nighttime, but the A320's and A318's lights work well in my simulator. I am not using the default landing lights texture because they are too yellow. I downloaded another texture from Internet which has a bluer tint.Prosdocimo wrote:About landing lights, probably there is an issue on nose gear's lights direction. If you watch at it by the front, you can see four lights. Two small lower (both taxi lights) and two upper (a small one on the left that is a taxi again, and a larger one on the right that is a landing light). Now these two upper lights seem badly oriented as you can see just a light spot down the gear and not forward. The bottom small lights and the wing's seem ok.
Edit. I looked on the web, it seems that landing and taxi lights are kept both on during landings and take off. This may help to increase the light intensity here.
-
- Posts: 501
- Joined: 20 Jan 2014, 21:27
Re: Project FMC simplified for Project Airbus
The change of the light beam vector/orientation from the landing and taxi lights (CTRL+ numpad 2,4,6, or 8 for down, L, R or up) is IMO sufficient to adjust the ground lighting.
-
- Posts: 277
- Joined: 10 Oct 2014, 12:05
Re: Project FMC simplified for Project Airbus
I didn't know it! I have to try next time thankswulfbindewald wrote:The change of the light beam vector/orientation from the landing and taxi lights (CTRL+ numpad 2,4,6, or 8 for down, L, R or up) is IMO sufficient to adjust the ground lighting.
Re: Project FMC simplified for Project Airbus
When I will less busy, I will write a small 2D gauge with some fucntion as :
- Open/close doors
- control jetway and pusback (turn pushback)
- set the landing beam
- refuel
......
- Open/close doors
- control jetway and pusback (turn pushback)
- set the landing beam
- refuel
......
-
- Posts: 501
- Joined: 20 Jan 2014, 21:27
Re: Project FMC simplified for Project Airbus
fdd_fr wrote:When I will less busy, I will write a small 2D gauge with some fucntion as :
- Open/close doors
- control jetway and pusback (turn pushback)
- set the landing beam
- refuel
......
In the meantime I propose to use a collection of FSX keyboard commands, please see here:
https://flyawaysimulation.com/downloads ... mands/get/
or a comprehensive and practical "onepager":
https://flyawaysimulation.com/downloads ... mands-pdf/
Re: Project FMC simplified for Project Airbus
I agree, but I deleted many of my shortcuts keys to assign my Ezdock cameras
Re: Project FMC simplified for Project Airbus
Link to download new beta (1.17) of the A321 CFM panel :
http://freenavdbgroup.com/Temp/A321FD-F ... 201.17.zip
This panel comes with a new AIR file, which has a new "wing lift versus wings Angle of attack" to improve aircraft attitude (more realistic pitch); previous version could have a negative pitch at high speed and low altitude (not realistic). I think that issue is solved.
please note that it requires that you use the aircraft.cfg file joined, because center of gravity has changed also (and some other minor data).
New panel :
- approach names can be longer in index list of approach
- fix LOC pointer strip on the PFD in backcourse mode (was reversed !, thanks wulf)
- a bug displayed "IAS" in descent page when no speed value
Now, I add these new features to A318 and A320 and I will update their panel next weekend.
I think that A321 flight dynamics are close to be completed; Maybe a last issue, about takeoff distance; I think that rooling distance is too long, according real aircraft, but your advice are welcome.
I think that I will adapt the new A321 Lift/angle of attack to A320 and A318
Francois
http://freenavdbgroup.com/Temp/A321FD-F ... 201.17.zip
This panel comes with a new AIR file, which has a new "wing lift versus wings Angle of attack" to improve aircraft attitude (more realistic pitch); previous version could have a negative pitch at high speed and low altitude (not realistic). I think that issue is solved.
please note that it requires that you use the aircraft.cfg file joined, because center of gravity has changed also (and some other minor data).
New panel :
- approach names can be longer in index list of approach
- fix LOC pointer strip on the PFD in backcourse mode (was reversed !, thanks wulf)
- a bug displayed "IAS" in descent page when no speed value
Now, I add these new features to A318 and A320 and I will update their panel next weekend.
I think that A321 flight dynamics are close to be completed; Maybe a last issue, about takeoff distance; I think that rooling distance is too long, according real aircraft, but your advice are welcome.
I think that I will adapt the new A321 Lift/angle of attack to A320 and A318
Francois
Re: Project FMC simplified for Project Airbus
Hi Carlos,The320Pilot wrote:Well, let me elaborate. UK2000 Manchester Xtreme shows the current runways (05L/R and 23L/R). I don't what are the runways in the default FSX.fdd_fr wrote:Ok. It will be done for next database update.The320Pilot wrote:Francois, I did a flight from EHAM to EGCC and I discovered a flaw in the EGCC approach data: current runways are 05L/23R and 05R/23L, but in the FD-FMC, the runways are 06L/24R and 06R/24L.
Could you please correct that? Thanks.
EGCC with current runway names is online
http://freenavdbgroup.com/download/FD_F ... 20name.zip
Francois
Re: Project FMC simplified for Project Airbus
New airports are online :
EDDP - Leipzig/Halle - Germany - by Philippe Bronier. comes with an updated AFCAD required to fix FSX wrong runway.
EDLV - Weeze - Germany - By Martien Van Rooten
KONT - Ontario - USA (California) by Wulf Bindewald
KTEX - Telluride - USA (Colorado) by Wulf Bindewald
KBWI - Baltimore/Washington - USA (Maryland) by Francois Dore
KMCI - Kansas City Intl - USA (Kansas) by Francois Dore
LFLL - Lyon saint Exupery - France - By jean-pierre Varnier
SBSP - Sao Paulo Congonhas - Brazil - by francois Dore
EGCC - Manchester - United Kingdom - By jean-pierre Varnier : version with current runway identifier for addon scenery (as UK Scenery)
Updates :
KMFR - Roghe Valley - USA (Oregon) v4.01 by Wulf Bindewald
SKCL - Cali - Colombia by Carlos Mario Diaz v4.04
SKBO - Bogota Eldorado - Colombia by Carlos Mario Diaz 4.04
Coming soon :
SBGR - Guarulhos Sao Paulo
EGPF - Glasgow
PANC - Anchorage
......
Note for airport creator,
I spoke some weeks ago about a fake airport called "XFMC", which allow to create terminal waypoints with free 2 lettrs ICAO region code.
After test, this fake airport cannot work if it is compiled in the AIRAC file. It seams that an airport file cannot contains "En Route" waypoints.
In this case, terminal waypoint was created, and appeared on the GPS/FMC map, but it was impossible to use it in a flight plan.
So, by compile this fake airport in a separate BGL file, all works fine and terminal waypoints can be added easily.
So when someone will need to create a terminal waypoint, I will add to the AIRAC file a second file called "XFMC.BGL" which contains the fake airport and all terminals waypoints with any 2 letters region code.
Begin your creation work, you can create a temporary XML file to add your terminal waypoints and compile with BGLCOMP.
Synthax :
<?xml version="1.0"?>
<FSData version="9.0"
xmlns:xsi='http://www.w3.org/2001/XMLSchema-instance' xsi:noNamespaceSchemaLocation="bglcomp.xsd" >
<Airport
region="FreenavDBgroup"
country="FreenavDBgroup Database"
city="XXFreenav"
name="XFD-FMC"
lat="-84.00"
lon="0.00"
alt="-9.0F"
magvar="0"
ident="XFMC">
<!-- Special XFMC waypoints with free 2 chars regional code -->
<Waypoint waypointType="IAF"
waypointRegion="SB" <!-- you can set here the region code of your choice -->
waypointIdent="AAAAA"
lat="-23.453306"
lon="-46.756047"
magvar="20">
</Waypoint>
<!-- end of terminal waypoints -->
</Airport>
With this exemple, synthax to write in the ECXEL file this terminal waypoint is :
Type = W
Region code = SB (brazil)
Airport icao = XFMC
Waypoint name = AAAAA
EDDP - Leipzig/Halle - Germany - by Philippe Bronier. comes with an updated AFCAD required to fix FSX wrong runway.
EDLV - Weeze - Germany - By Martien Van Rooten
KONT - Ontario - USA (California) by Wulf Bindewald
KTEX - Telluride - USA (Colorado) by Wulf Bindewald
KBWI - Baltimore/Washington - USA (Maryland) by Francois Dore
KMCI - Kansas City Intl - USA (Kansas) by Francois Dore
LFLL - Lyon saint Exupery - France - By jean-pierre Varnier
SBSP - Sao Paulo Congonhas - Brazil - by francois Dore
EGCC - Manchester - United Kingdom - By jean-pierre Varnier : version with current runway identifier for addon scenery (as UK Scenery)
Updates :
KMFR - Roghe Valley - USA (Oregon) v4.01 by Wulf Bindewald
SKCL - Cali - Colombia by Carlos Mario Diaz v4.04
SKBO - Bogota Eldorado - Colombia by Carlos Mario Diaz 4.04
Coming soon :
SBGR - Guarulhos Sao Paulo
EGPF - Glasgow
PANC - Anchorage
......
Note for airport creator,
I spoke some weeks ago about a fake airport called "XFMC", which allow to create terminal waypoints with free 2 lettrs ICAO region code.
After test, this fake airport cannot work if it is compiled in the AIRAC file. It seams that an airport file cannot contains "En Route" waypoints.
In this case, terminal waypoint was created, and appeared on the GPS/FMC map, but it was impossible to use it in a flight plan.
So, by compile this fake airport in a separate BGL file, all works fine and terminal waypoints can be added easily.
So when someone will need to create a terminal waypoint, I will add to the AIRAC file a second file called "XFMC.BGL" which contains the fake airport and all terminals waypoints with any 2 letters region code.
Begin your creation work, you can create a temporary XML file to add your terminal waypoints and compile with BGLCOMP.
Synthax :
<?xml version="1.0"?>
<FSData version="9.0"
xmlns:xsi='http://www.w3.org/2001/XMLSchema-instance' xsi:noNamespaceSchemaLocation="bglcomp.xsd" >
<Airport
region="FreenavDBgroup"
country="FreenavDBgroup Database"
city="XXFreenav"
name="XFD-FMC"
lat="-84.00"
lon="0.00"
alt="-9.0F"
magvar="0"
ident="XFMC">
<!-- Special XFMC waypoints with free 2 chars regional code -->
<Waypoint waypointType="IAF"
waypointRegion="SB" <!-- you can set here the region code of your choice -->
waypointIdent="AAAAA"
lat="-23.453306"
lon="-46.756047"
magvar="20">
</Waypoint>
<!-- end of terminal waypoints -->
</Airport>
With this exemple, synthax to write in the ECXEL file this terminal waypoint is :
Type = W
Region code = SB (brazil)
Airport icao = XFMC
Waypoint name = AAAAA
Re: Project FMC simplified for Project Airbus
Hello Francois,
16 May 2015,
Solution :
Give the waypoint an owner
you give Waypoint AAAAA an Owner XFMC that's it !
Look here Terminal Waypoints
Cheers,
Thomas
That's what I said.With this exemple, synthax to write in the ECXEL file this terminal waypoint is :
Type = W
Region code = SB (brazil)
Airport icao = XFMC
Waypoint name = AAAAA
16 May 2015,
Solution :
Give the waypoint an owner
you give Waypoint AAAAA an Owner XFMC that's it !
Look here Terminal Waypoints
Cheers,
Thomas
Re: Project FMC simplified for Project Airbus
I agree thomas, but in first, I placed this airport in the AIRAC file with all "en route" waypoint, and that didn't work.moskito-x wrote:Hello Francois,
That's what I said.With this exemple, synthax to write in the ECXEL file this terminal waypoint is :
Type = W
Region code = SB (brazil)
Airport icao = XFMC
Waypoint name = AAAAA
16 May 2015,
Solution :
Give the waypoint an owner
you give Waypoint AAAAA an Owner XFMC that's it !
Look here Terminal Waypoints
Cheers,
Thomas
The Fake airport (and its terminal waypoints must be placed in a separate BGL file, only for it. Airport file cannot have "en route" waypoint otherwise, terminal waypoints cannot be inserted in a flight plan (they appears on the GPS map, but you cannot select them.
I spent 1 month to understand this issue !!!
Thanks for your idea.
Francois
Re: Project FMC simplified for Project Airbus
I am preparing new final Aircrafts packages (A318, A320 and A321) version 1.20. with all last new features and bug fixed (many thanks to Wulf for help me to debug).
I think that new packages will be ok next weekend.
If you want, to wait...you can download the last AIR files for each aircraft (A318, A320CFM and A320 IAE) with new Wing lift and Angle of attack, for a mere accurate and realistic attitude.
The 3 air files are here : http://freenavdbgroup.com/Temp/A318-A32 ... pdated.zip
Very important, you have to edit each aircraft.cfg file to change the following setting :
in the [Flight_Tuning] section,
set "cruise_lift_scalar" setting to 1.00 (actual must be between 1.20 and 1.35 according aircraft).
Value becomes standard with these new AIR files.
Francois
I think that new packages will be ok next weekend.
If you want, to wait...you can download the last AIR files for each aircraft (A318, A320CFM and A320 IAE) with new Wing lift and Angle of attack, for a mere accurate and realistic attitude.
The 3 air files are here : http://freenavdbgroup.com/Temp/A318-A32 ... pdated.zip
Very important, you have to edit each aircraft.cfg file to change the following setting :
in the [Flight_Tuning] section,
set "cruise_lift_scalar" setting to 1.00 (actual must be between 1.20 and 1.35 according aircraft).
Value becomes standard with these new AIR files.
Francois
Re: Project FMC simplified for Project Airbus
Latest panel 1.15, A320, altitude button not responsive to mouse wheel. No response at all on the ground, in the air would jump from 2700-5400 so it would double itself. This is with no flight plan, flying selected.
Re: Project FMC simplified for Project Airbus
Hi Fliptod,
I did a test and no problem with ALT knob in selected mode, without flight plan.
Maybe had you other circumstances....or did a specific action....
Francois
I did a test and no problem with ALT knob in selected mode, without flight plan.
Maybe had you other circumstances....or did a specific action....
Francois
Re: Project FMC simplified for Project Airbus
After many adjustments and tests, I present the final A321 panel beta 1.19 and flight model (I hope ! )
You can download here : http://freenavdbgroup.com/download/Pane ... 201.18.zip
- New AIR file, with more thrust to taxiing and more takeoff power ( from 90-92% N1 and more )
- New aircraft.cfg file with new Flaps's pitch and lift effectiveness, and some minor adjustments
- New panel : fix some latence when ALT to ALT CST* readings and with G/S* to G/S, fix some minor bugs in the PFD.
- Spoilers can be extand at 100% in managed descent now
- change conditions which toggle ECAM checklist from Standard to landing inhibit.
I will update Airport database tomorrow
I will prepare aircrafts new packs (include A318/A320/A321) with this new panels for last week
Sorry for the delay, but manu things to do !
Francois
You can download here : http://freenavdbgroup.com/download/Pane ... 201.18.zip
- New AIR file, with more thrust to taxiing and more takeoff power ( from 90-92% N1 and more )
- New aircraft.cfg file with new Flaps's pitch and lift effectiveness, and some minor adjustments
- New panel : fix some latence when ALT to ALT CST* readings and with G/S* to G/S, fix some minor bugs in the PFD.
- Spoilers can be extand at 100% in managed descent now
- change conditions which toggle ECAM checklist from Standard to landing inhibit.
I will update Airport database tomorrow
I will prepare aircrafts new packs (include A318/A320/A321) with this new panels for last week
Sorry for the delay, but manu things to do !
Francois
Last edited by fdd_fr on 27 Mar 2016, 07:42, edited 2 times in total.
-
- Posts: 277
- Joined: 10 Oct 2014, 12:05
Re: Project FMC simplified for Project Airbus
Hi thanks, keep up the great work! It asks me a password to downolad. I can't download it
Re: Project FMC simplified for Project Airbus
Yes, must have been something residual. Worked fine this time. The first time I didn't fill in any performance data. This may have contributed.